Saturday, 3 March 2012

Moulding wk1

Yesterday afternoon I used brass shim to section off the top part of the left leg ready for moulding. The plan is to start at the bottom and work my way up the front until the neck is fully supported by the fibreglass. This means I'll be able to cut the support wire at the back of the head and clean this up before moulding that section. Hopefully the photos explain the order of things...

Most sections are big and simple enough to be walled up with the shim but the hands and feet will need to be clay walled. Also, for the time being, I'll be keeping the removable platform in place to help the scaff. pole support the sculpture during the majority of the moulding. Then I'll take it away to glass the underside...

Monday, 27 February 2012

Hoisting day!

I nervously took photos of my sculpt (w/o the arms) being hoisted up the side of the workshop - the resin room is on the first floor and it was definitely too heavy to carry up the spiral staircase. The awkward look on his face is quite fitting for this situation!




It was then lifted onto a low trolley and wheeled round to the resin room. Here's some photos I took just before I started moulding...






Friday, 24 February 2012

New eye blank close-ups

So yesterday I got the right sized eye blanks into the sculpt and positioned them exactly how I wanted them to look in the final model.


The direction of the eyes make the Kijimuna looks like he's just been caught in the middle of something. I grabbed an average sized person from Modelmaking and made sure the eyes were looking at them so most people at our end-of-year show will think it's looking right at them.

Thursday, 23 February 2012

Eyes

The glass eyes I ordered from Tohickon finally arrived today - Since before I started sculpting I've been trying to source a pair of 40mm eye blanks to use in the sculpt that would match the ones from Tohickon, the closest I had was 38mm (3/4 round blanks instead of the 1/2 blanks that were needed) so those were the ones I've sculpted round until today. I made a quick Otoform mould of one of the Tohickon eyes, cast out 2 fast cast blanks and replaced the 38mm ones with these so the eye sockets in the final model would be exactly the right size. I also drew on exactly where the pupil's would be. A bit last minute but worth it because this will save me time at the end when I would have had to bulk out the sockets to make them fit.


Saturday, 4 February 2012

Colour Test 2

Second go at colouring this photo, using the same skin base, this time with a more red/pink type pattern that would cover the back and travel round the shoulders and face. I'd like to do a more interesting paint job than in previous projects...

Friday, 3 February 2012

The Sculpt

So I started massing out today, I'm conducting a time-lapse on the whole process and here's the first one - of course these earlier videos look more interesting because the changes are more drastic but I hope to move the camera steadily closer as I get into more detail...


NOTE TO PAUL: VIDEO 'SERVER REJECTED' AT THE MOMENT - WILL TRY AND RE-POST SOON BUT WILL GIVE YOU A COPY OF THE TIME LAPSES ANYWAY...

Thursday, 2 February 2012

Colour Test 1

I've taken a 45 degree photo of the head maquette and coloured it in Photoshop. I've added a rough sketch of hair to give an indication of what the skin might look like on the final model. This is the first colour test I've done, it's just a simple mottled pattern but I still quite like it. The skin tone I did for the Capramostro project was probably the simplest form of skin colouring, so it would be nice if I could do something a little more exciting for this model.

Armature 2

I've attached a loop of wire to support the head, bridged the arms onto the solid box section in the shoulders and bulked out the main parts of the armature with plaster bandage. Tomorrow I hope to begin massing out in smooth buff clay - I want to sculpt in WED clay but due to the size of the sculpt I thought it'd be best to bulk out with a cheaper clay and use the wed on the surface to hold in more moisture and achieve sharp detail.


Wednesday, 1 February 2012

Starting the armature

Yesterday, I worked out several different options for the armature set up - it's not just about the sculpt being supported but at what level it is best sculpted at and how it will be transported. The size of my project means transportation from the modelmaking studio to the upstairs resin room in the workshop will have to happen via a hoist. I had to measure the hoist cage carefully to make sure the moveable part of the armature base and the sculpt will fit safely in it. I did some diagrams below showing some of the options, eventually settling on option 2. A lowerable platform was added to the design to raise the sculpt from the base it's fixed to to allow the underside of the sculpt to be fibreglassed once the rest has been moulded/supported.


This second diagram was to work out how high the table had to be so the top of the sculpt wasn't too high for me to reach. I scaled up the previous sketch of the sitting Kijimuna to match the head size of the full-size WED clay head maquette and used this to measure roughly how tall the sculpt would be in the end.


I constructed the table and sourced some scaffolding pole and key clamps on Friday, so on Monday, yesterday and today I made the rest of the base and fixed some of the armature to the scaff pole:


I cut the leg wire as one long piece and made sure the measurements were equal on both sides. I made the hand and feet wire into loops so that wires can be added to the fingers / toes if need be...


I used bridger (Isopon P40) to fix the armature together. In order to mould the arms separately, I had to make sure they were easily deattachable from the rest of the sculpt. I used solid and hollow metal box section to create a 'slot-on/slot-off' section in the shoulder to help with this:

Thursday, 26 January 2012

Teeth 3

Today I cast out the final set of teeth. I used a dental acrylic kit from 'M R Dental' and chose a pre-coloured powder (pink) to go with the liquid monomer because I knew I would only be using the acrylic for the gums. Pictured below was my set up:


I chose a cold cure acrylic which means it does not need to be cast under a controlled heat whilst also under pressure (I would need an autoclave for this). I used a hydraulic pressure pot which was recommended to me by Darren and another industry professional to use for this purpose. I set up in our uni's polyester resin room which had the best ventilation and was wearing gloves and a respirator throughout. The photos below show an all-pink acrylic tester I did to practice with the material and one of the original gum sculpts with the teeth taken out and 'glued' into it's mould with tiny amounts of vaseline. The teeth are also acrylic, so they stayed imbedded in the acrylic gums (which means one chance to get them right!):


The next photos show me mixing the acrylic, pouring it into the mould (with the teeth imbedded), the mould in the pressure pot chamber after the acrylic had reached it's snap cure making it ready to be put in water and before the lid and pressure was put on. The last photo shows one half of the final set after de-moulding, they were ready to de-mould after roughly 20 min...




These teeth will now be put aside until the last minute, then they'll be coloured up and inserted into the model at the same time as the glass eyes.

Wednesday, 25 January 2012

Teeth 2

Pictures below are the moulds for my teeth with the original sculpts pulled out- I'm going to leave the teeth in the sculpted gums until they need to be embedded into the moulds so I don't loose them or forget what order / position they're in. I then made blanks of the teeth from fast cast, with a bit of tweaking, these will go into the Kijimuna sculpt to be sculpted around and will be screwed into the inside of the fibreglass mould like the eyes.



Instead of having to integrate an additional silicone plug into the mould to stop the Platgel from filling up the mouth cavity, I decided to make the mouth cavity and the teeth into one solid unit so it is easier to build the inside core around and so I don't have to worry about the Platgel sticking to the silicone plug (which would also have to be a platinum silicone!). I fixed the teeth into a slightly open position that I was happy with and filled in the gap with filler and Milliput, It was difficult to imagine what shape to make the cavity because I am essentially sculpting a negative space, but I remembered to leave the top and bottom of the teeth blanks clear so there will be a recess in the mouth where the real teeth can glue into. I also think the teeth will be open enough to warrant making a tongue to go inside...

Tuesday, 24 January 2012

Teeth!

So after deciding to have mostly human-looking teeth, I bought some loose acrylic ones off eBay to use to assemble my own upper and lower sets. I haven't properly scheduled the making of the teeth into the project so I figured sculpting the gums would be challenging enough let alone attempting to sculpt replicas of actual teeth - in industry the teeth (if close to a humans') would most likely be bought and then adapted to a fit a design anyway.

My friend Darren Grassby is a dental lab technician based in Bradford, he produces false teeth and dentures for FX purposes in his own time, has worked on teeth for Harry Potter and gave me some tips on the processes involved in making a set of good teeth (dentures or otherwise). Using the correct materials is important for getting the right look so I have ordered a kit of dental acrylic (pink powder and liquid monomer) to cast the gums in. He lent me a set of his own teeth to look at and I used these as reference when sculpting gums for my teeth. I considered using dental wax to sculpt the gums, pictured below (this is used often by dental technicians) but I am unfamiliar sculpting with this and decided the properties of Monster Clay would work in a similar way.





Pictured above is a collection of the teeth I bought pushed into some plasteline just to give me an idea of what order I wanted them to be in and what shades I wanted to use. Pictured below is the finished set of gums with the chosen teeth implanted. I made moulds of these this afternoon and will demould tomorrow.